About
All feedback (1,360)
e-specialized (7406)- Feedback left by buyer.
Past month
Verified purchase
Good buyer, prompt payment, valued customer, highly recommended.
foreigndomesticautoparts (67583)- Feedback left by buyer.
Past month
Verified purchase
Good buyer, prompt payment, valued customer, highly recommended.
star-autostore (866)- Feedback left by buyer.
Past month
Verified purchase
Good buyer, prompt payment, valued customer, highly recommended.
jetmax (1645)- Feedback left by buyer.
Past month
Verified purchase
Good buyer, prompt payment, valued customer, highly recommended.
bold_auto_parts (27497)- Feedback left by buyer.
Past 6 months
Verified purchase
Good buyer, prompt payment, valued customer, highly recommended.
second.sale (3279328)- Feedback left by buyer.
Past 6 months
Verified purchase
Good buyer, prompt payment, valued customer, highly recommended.
Reviews (13)
Jun 22, 2017
01 TT fwd
Item arrived and paint match was close to the factory color. Clear coat was good and could use more wet sanding. I installed it with double sided tape all around the mounting area perimeter. Then applied liquid nails toward the center on the ends wheee the double sided tape left a space. Just enough so that when pressed on to the oem spoiler, the glue had room to slightly spread itself into the area where there was no tape. Then once it was pressed on I used the masking take to tape all sides to hold it in place for several hours. Hopefully this will hold with the liquid nails and double sided tape. Looks aggressive but not an eye sore. Couldn't ask for a better deal paint and fitment. A for overall experience.
Feb 02, 2018
Looks nice but needs modifications
Like the title says, the seats look great and good craftsmanship but they are not the correct height for the main cushion section where you sit. The rails supplied dont work with the sliders. I had to get a different set of sliders. This was tested on 91 240sx. The main cushion is way too thick and should be only half of what it is in height wise. As of now, my head is about 2.5 inches from the roof/ headliner... this can be very serious in roll over or accident that can force the drivers head through the headliner. I would say they are better than stock only if they were thinner in the area where you sit. Would I recommend these? Yea if you want them in a truck... but for a car, specs are not right at all.
* for this to work*
I needed 8 additional nuts and sized washers to connect them properly to the bracket. I had to undo the seat main cushion claw rings that hold the main cushion cover from the underside front. Then tear out the middle cover claw rings and slide the cushion out through the front, lifting the cushion pad rear lip. Measured from the top of the pad 1.5 inches at the front and tapering to 1 inch to the rear. I used a sharp blade and cut straight to 90 degrees across as possible. Reverse install and it worked! I now sit only slightly higher than stock due to the sliders. But its within spec now. Shifting and pedal reach is good now. Definitely better holding than stock. If this was all done at the get go from seller, it would be 5 stars and better deal than sparco.
Feb 21, 2022
323/328 headers e46 M52/M54
I wasn’t sure if these were good but at the price, i gave it a shot. Removing the stock headers was the hardest part. I had to get my own hardware since it didn’t come with any to mount to the exhaust pipe. The minus one star rating was due to the O2 sensor bung on the front header being directly below the rear header pipe and there’s no way to fit an O2 sensor. I had to use a 90’ degree O2 sensor elbow to fit the O2 on. Also the clearance is very tight, but not touching on the passenger side engine mount. With it being so tight, removing the motor mount heat shield and the engine bracket heat shield made it possible to fit without touching. The header flange at the exhaust connection had holes that were slightly smaller than my hardware I had so I had to widen them with a drill but. I could’ve just took measurements before hand and bought bolts to match the header but was too lazy to go to the hardware store again lol. The supplied gaskets worked well and so far after initial start up, there is no exhaust gas leaks. Despite the O2 location issues it’s a heck of a deal. These are for 323/328 M52/M54 engine DUE TO FLANGE TO EXHAUST ORIENTATION . Will NOT work on 325/330. It fits near perfect just minor hiccups but I’m highly satisfied. Have not test drives it yet only idle check and it’s louder.